BMW MOA Tech Series
1979 BMW R65 · Airhead · Engine

Airhead Autopsy: BMW R65 Engine Teardown

Wes Fleming and George Mangicaro tear into a blown $43 BMW Airhead engine to find out what failed - and what the damage can teach us.

Disassembled BMW Airhead boxer engine during the Airhead Autopsy BMW R65 engine teardown
BMW R65 Engine Teardown

A dead engine with a lot left to teach.

The BMW MOA's Wes Fleming bought this 1979 BMW R65 engine at a swap meet for $43. We knew it was blown, but not why, how badly or which parts had failed. With one day in the shop, Wes and George Mangicaro began dismantling the boxer engine and following the mechanical evidence. Airhead Autopsy documents that teardown from the outside in.

Year1979
ModelBMW R65
FamilyAirhead
SystemEngine
Watch the Series

Airhead Autopsy Episodes

Follow the teardown in order as the R65 engine comes apart and the clues to its failure begin to emerge.

Episode 01

The Autopsy Begins

The mystery R65 engine goes on the lift and the teardown begins. With no known diagnosis, every component removed becomes another clue.

Watch Episode 1 on YouTube →
Episode 02

Deeper into the Boxer

The investigation continues as more of the BMW Airhead engine comes apart and the condition of its internal components becomes clearer.

Watch Episode 2 on YouTube →
Episode 03

(Wrist pin) Resistance is futile

The BMW R65 teardown continues as Wes Fleming and George Mangicaro remove the pistons and discover some disconcerting damage.

Watch Episode 3 on YouTube →
Episode 04

Of con rods and special tools

Borrowed tool in hand, Wes and George are able to get the connecting rods out and get more clues about the engine's failure.

Watch Episode 4 on YouTube →
Episode 05

Sun's out? Studs out!

George shares (and Wes implements) a quick and easy way to extract the cylinder studs. It might be the easiest and most obvious tip we've ever shared.

Watch Episode 5 on YouTube →
Episode 06

Flywheel removal

We make it look WAY harder than it is AND use an inappropriate tool to boot! In the end, we win, so that's what really matters.

Watch Episode 6 on YouTube →
Episode 7

Alternator removal: A shocking development

Wes and George tackle the R65's alternator assembly, using a special removal bolt to separate the rotor from the crankshaft. Things get a little destructive along the way, and a stator may or may not have been harmed in the making of this episode.

Watch Episode 7 on YouTube →
Episode 08

What's the point? Inside the points-in-can

Wes and George remove the R65's points-in-can ignition unit and open it up to see how this compact assembly works. If you've never seen what goes on inside one of these things, here's your chance.

Watch Episode 8 on YouTube →
Episode 09

What's behind the timing cover?

Wes and George remove the R65's front timing cover to expose the timing components, then tackle the timing chain and its tensioners. The only question is how many bolts Wes will miss along the way.

Watch Episode 9 on YouTube →
Episode 10

Exposing the oil pump

Buried deep in the engine but accessible from outside the block, the R65's oil pump is next on the disassembly list. Wes and George take it apart and examine this essential piece of the lubrication system.

Watch Episode 10 on YouTube →
10 of 11 serialized episodes are currently available.

New episodes will be added to this page as the Airhead Autopsy continues.

About the Teardown

Mostly ordinary tools. One very dead Airhead.

Most of the work is accomplished with ordinary hand tools, including hex wrenches and standard sockets, with only a handful of specialty tools required. That makes the series a useful close-up look at BMW Airhead engine construction as the R65 comes apart.

A note about the disassembly

This engine was never going to be saved, rebuilt or returned to service. Some techniques shown in the series are more destructive than we would recommend on an engine you intend to preserve or rebuild.

Filmed at Morton's Motorcycles

Thanks for giving the autopsy a place to happen.

Many thanks to Morton's Motorcycles in Fredericksburg, Virginia, for providing the shop space and motorcycle lift that made this project possible.

Visit Morton's Motorcycles ↗
Support BMW MOA Tech
Your membership helps make projects like Airhead Autopsy possible.

BMW MOA membership supports original technical content, rider education and practical resources built for the motorcycle community. Joining helps us keep creating and sharing projects like this one.

BMW MOA Tech

Technical knowledge, practical projects and motorcycle experience from the BMW MOA community.